fa4be5902e
This automation identifies hosts without monitors and ensures that at least two nodes are available. It then adds two monitors, applies rook-ceph, and validates the application and health status. The test proceeds to remove the monitors, lock and unlock nodes, delete host-fs entries, and re-apply rook-ceph as required. Finally, it verifies that rook-ceph health returns to a stable state. Change-Id: Ib2b06c381bca15b6908f591af2f9097dad3b54a9 Signed-off-by: tleal <tiago.leal@windriver.com>
48 lines
2.7 KiB
INI
48 lines
2.7 KiB
INI
[pytest]
|
|
; --tb=no Prevent Pytest from logging stacktraces. This is handled by the framework internally.
|
|
; -s Show all output during test execution
|
|
addopts = --tb=no -s
|
|
|
|
markers=
|
|
# Lab Specific Requirement Markers
|
|
lab_is_simplex: mark tests that run on simplex labs
|
|
lab_is_duplex: mark tests that run on duplex labs
|
|
lab_has_standby_controller: mark tests that run using a standby controller
|
|
lab_has_low_latency: mark tests that need low latency
|
|
lab_has_non_low_latency: marks tests that need non low latency
|
|
lab_has_sriov: mark tests that have sriov
|
|
lab_has_hyperthreading: mark tests that require a hyperthreaded host
|
|
lab_has_no_hyperthreading: mark tests that require a host without hyperthreading
|
|
lab_has_worker: mark tests that require a worker
|
|
lab_has_storage: mark tests that require storage
|
|
lab_is_ipv4: mark that lab needs to be ipv4
|
|
lab_is_ipv6: mark that lab needs to be ipv6
|
|
lab_has_n3000: mark tests that require a N3000 device
|
|
lab_has_fpga: mark tests that require an FPGA based device
|
|
lab_has_acc100: mark tests that require an ACC100 device
|
|
lab_has_acc200: mark tests that require an ACC200 device
|
|
lab_has_columbiaville: mark tests that require a Columbiaville-family device
|
|
lab_has_min_space_30G: mark tests that require at least 30 GB of free disk space
|
|
lab_has_processor_min_2: mark tests that require at least 2 processors
|
|
lab_has_page_size_1G: mark tests that require page size 1G
|
|
lab_has_ae_interface: mark tests that need AE interface
|
|
lab_has_physical_interface_min_2: marks tests that require 2 or more physical interfaces
|
|
lab_has_bond_interface: mark tests where the host must have a bond interface
|
|
lab_has_storage_6_osd: mark tests that use specific labs with 6 or more OSDs
|
|
lab_has_subcloud: mark tests that require at least one subcloud
|
|
lab_has_min_2_subclouds: mark tests that require at least 2 subcloud
|
|
lab_has_compute: mark tests that require at least one compute node
|
|
lab_has_min_3_compute: mark tests that require at least 3 compute nodes
|
|
subcloud_lab_has_compute: mark tests that require at least one subcloud containing at least one compute node
|
|
lab_has_secondary_system_controller: mark tests that require a secondary system controller
|
|
lab_has_ptp_configuration_compute: mark tests that requred ptp_configuration_expectation_compute.json5
|
|
lab_rook_ceph: mark tests that require rook-ceph application applied
|
|
lab_is_aio: mark labs without worker nodes
|
|
#TODO: add 'lab_has_bmc_ipmi', 'lab_has_bmc_redfish', 'lab_has_bmc_dynamic', and 'lab_bmc_sensor'
|
|
|
|
|
|
# Priority Markers
|
|
p0: mark test priority as p0
|
|
p1: mark test priority as p1
|
|
p2: mark test priority as p2
|
|
p3: mark test priority as p3 |